RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Len Todd
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Forum: RC Jets
12-08-2019, 01:47 PM
Replies: 1,631
Views: 335,315
Posted By Len Todd

Yes. The nose wheel sees the Mercury's gyro...

Yes.

The nose wheel sees the Mercury's gyro effect via the mix I have in the Transmitter that ties the nose wheel to the rudder channel. I am using Spektrum SRS Rxers. I attached my initial setup...
Forum: RC Jets
12-08-2019, 11:39 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

I have the Mercury PBox and the Xicoy LGC15...

I have the Mercury PBox and the Xicoy LGC15 installed in my larger T-1. I use the Mercury gyro on the three flight control surfaces and the LGC 15 operates the gear, brakes, nose door and steering....
Forum: RC Jets
11-22-2019, 11:55 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

If the brakes are weak, then things most-likely...

If the brakes are weak, then things most-likely are not adjusted correctly. They typically lock up around 50-60% as indicated by the LED strings. For a mini, they even lock up sooner because the...
Forum: RC Jets
11-18-2019, 06:10 PM
Replies: 1,631
Views: 335,315
Posted By Len Todd

I run my LGC 15 at 7.0 VDC via a 10 Amp Castle...

I run my LGC 15 at 7.0 VDC via a 10 Amp Castle Creations voltage regulator. They work great. Once you set the LGC 15 up correctly you will love it and the brakes on your plane!
Forum: RC Jets
11-18-2019, 06:20 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

If you run the gear to the mechanical stop on a...

If you run the gear to the mechanical stop on a battery w/o the controller, the gear motor will burn out. There are current limiters in the controller. If you use too high of a voltage, the gear...
Forum: RC Jets
08-18-2019, 09:25 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

Plane owner came 3 hours to our field to get some...

Plane owner came 3 hours to our field to get some stick time toward a waiver. Plane owner indicated to us that the plane was flown before he came to our field and it flew O.K.. We spent several hours...
Forum: RC Jets
08-18-2019, 05:50 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

Regarding the crack in the wing: This is not the...

Regarding the crack in the wing: This is not the first mini I have seen with that specific crack. IMHO, the main gear mounts are not sufficient. The gear comes loose and the gear's motor...
Forum: RC Jets
08-05-2019, 04:49 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

Flap servos can fail when flying full flap at...

Flap servos can fail when flying full flap at high speeds. Depends on how much torque capability they have and in the case of flaps, how long they are fully deployed and how fast the plane is flying...
Forum: RC Jets
08-04-2019, 11:34 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

When setting up the plane, for the flaps, I...

When setting up the plane, for the flaps, I always set the travel down to 10-20% and the set the linkage for half flap. Then, I run the travel out to where I want them to be. At the flaps up position...
Forum: RC Jets
08-04-2019, 11:16 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

Assuming t he Mini gear is similar to the larger...

Assuming t he Mini gear is similar to the larger T-One's as they are both JP design, as I understand it:

I lost one of the shims. Found it a couple months later on a magnet. In the meantime, I...
Forum: RC Jets
08-04-2019, 05:56 AM
Replies: 1,631
Views: 335,315
Posted By Len Todd

Deleted

Deleted
Forum: RC Jets
07-27-2019, 06:22 PM
Replies: 1,631
Views: 335,315
Posted By Len Todd

What are you guys doing to beef up the landing...

What are you guys doing to beef up the landing gear mounts? I saw one yesterday with the gear falling out and it was flown once before. I was told the wood screws used were what the OEM provided....
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.